View NVR-0204_6375896.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

user manual ver. 1.1 NVR-0204/0208/0216 4-ch/8-ch/16-ch network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual english use r s manual levelone network video recorder table of contents copyrights, trademarks & gpl 3 system requirements 4 product description 5 hardware illustration 6 i/o ports and rs-485 7 leds definition 8 install hard disk 9 connect to the nvr 12 1. live view 16 1.1 retrieve cameras video stream 18 1.2 retrieve cameras status 18 1.3 perform sequence viewing 19 1.4 ptz control 20 1.5 perform ptz preset viewing 21 1.6 live video control buttons 23 1.7 change web ui display language 26 2. playback 27 2.1 methods to search playback videos 28 2.2 export playback videos to avi files 34 3. system setup 36 3.1 system configurations 36 3.1.1 network settings 36 3.1.2 time and date 38 3.1.3 user account 39 3.1.4 group privilege 40 3.1.5 disk setup 42 3.2 channel configurations 43 3.2.1 add a camera 43 3.2.2 osd settings 46 3.2.3 ptz preset settings 47 3.2.4 ptz preset sequence 48 3.2.5 e-map monitor 49 3.3 event configurations 51 3.3.1 general settings 51 3.3.2 i/o settings 52 3.3.3 event servers 54 3.3.4 event triggers 58 3.4 recording configurations 60 3.4.1 general settings 60 3.4.2 schedule recording 62 3.5 system options 64 3.5.1 device information 64 3.5.2 logs and reports 65 3.5.3 maintenance 65 reboot the nvr 66 reset the nvr to factory default 67 hardware reset procedure 67 3.5.4 do status 68 3.5.5 disk status 68 3.5.6 ups configuration 69 3.6 nvr recording time for reference 70 2 2 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder copyrights , trademarks & gpl copyright ? 2009 digital data communications gmbh. trademarks levelone NVR-0204/0208/0216 network video recorder (nvr) is a registered trademark of digital data communications gmbh. microsoft and windows are registered trademarks of microsoft corporation. all other trademarks mentioned in this document are trademarks of their respective owners. disclaimer this document is intended for general information p urposes only, and due care has been taken in its preparation. any risk arising from the use of this information r ests with the recipient, and nothing herein should be construed as constituting any kind of warranty. digital data communications gmbh reserves the right to make adjustments without prior notification. all names of people and organizations used in these documents examples are fictitious. any resemblance to any actual organ ization or person, living or dead, is purely coincidental and unintended. general public license this product incorporates open source code into the software and therefore falls under the guidelines governed by the general public license (gpl) agreement. adhering to the gpl requirements, the open source c ode and open source license for the source code are available for free download at http://global.level1.com . if you would like a copy of the gpl or other open s ource code in this software on a physical cd medium, levelone (digital data communic ations) offers to mail this cd to you upon request, for a price of us$9.99 plus th e cost of shipping. 3 3 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
http://www..net/ datasheet pdf - http://www..net/
5 english use r s manual levelone network video recorder system requirements the following are minimum system requirements for t he system to operate levelone network video recorder (nvr): operating system microsoft? windows? 2000 professional, windows? xp professional (32 bit) or windows? server 2003 (32 bit) browser microsoft internet explorer 6 or above cpu minimum intel? pentium? 4 2.4 ghz or higher (dual c ore is recommended) ram minimum 1 gb of ram, 2gb or above is recommended network minimum 10/100 ethernet (gigabit ethernet is recomm ended) graphics adapter agp or pci-express, minimum 1024x768, 16 bit colors . (we highly recommend to work above the 1024 x 768 r esolution to get the full experience of the software) . make sure your display dpi setting is set to defaul t at 96dpi . to set dpi value, right-click on desktop, choose s ettings tab >> advanced >> general contents inside the installation cd . adobe acrobat reader . levelone device search utility levelone nvr management software . users manual . quick installation guide default settings ip address dhcp address username root password root levelone nvr series network video recorder 4 http://www..net/ datasheet pdf - http://www..net/
6 english use r s manual product description the levelone network video recorder is designed for use within a surveillance system, and performs recordings and pl aybacks pictures from network cameras in the system. it is a recording de vice using a hard disk drive to record camera pictures instead of using video ta pes so that pictures recorded by repeated overwriting will not experience deterio ration of the recorded picture quality. up to 4 (for NVR-0204) or 8 (for nvr-0208) or 16 (for nvr-0216) cameras can be connected via a network and it is possible t o record their camera pictures. it is possible to perform the settings or operate t he nvr using a web browser installed on a pc connect to a network, or remote c ontroller. recorded video can be played back from remote site by a pc. up to 4 pc s (web browsers) can access this unit concurrently and it is possible to perform the settings and operate this unit. the nvr is compatible with most major brand c a m e r a s a n d i t s a b i l i t y t o automatically search and find the av ailable cameras on the network can greatly reduce the user effort when exp anding the system. . advance ptz control . various types event alerts . pure web based administration . linux-embedded operating system . . export recorded videos to avi . compatible with major brand cameras . high quality live/playback videos . levelone smart camera search 4 5 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
7 english use r s manual hardware illustration (front) 6 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
8 english use r s manual i/o ports and rs-485 (rear) pin signal 1 dcin 2 gnd 3 ~ 10 alarm input 11 out1 12 out2 13 out3 14 out4 15 rs485+ 16 rs485- 7 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
9 english use r s manual leds definition green solid green when the hard disk is mounted and being accessed red solid red for disk fail hdd x 2 amber solid amber when disk is full blinking when recycling amber solid amber for activity on a 1g bps network. network green solid green for activity on a 10/100 mbps net work. amber blinking during firmware upgrade green shows solid green for normal operation. blinking green when firmware upgrade is done status red flashes red for failed firmware upgrade. green normal operation red system off (power adapter remains plugged in) power amber blinking amber indicating device is initializing red blinking when an alarm occurs alarm none when alarm is reset green solid green, live connected with no event or record ing activity amber blinking amber, manual or event recording is being performed amber solid amber, schedule or continuous recording is being performed camera ledx16 (8 for nvr- 0208, 4 for NVR-0204) red recording is set but no video from camera 8 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
10 english use r s manual install hard disk start by removing the screws on the side: push the top housing forward then lift it up . the nvr supports sata i or sata ii hard disks . the nvr supports max. 1tb per hard disk and it supports total of 2 hard disks 2tb) 9 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
1 1 english use r s manual remove the hard drive cover plate pull out the hard drive tray holder place the hard drive on the tray and push it inward to secure the hard drive 10 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s man ual levelone network video recorder connect the sata cable to the hard drive put the hard drive tray cover plate back place the top housing back and secure it with the b ottom housing 11 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder connect to the nvr there are various ways you can connect to the nvr a nd below are the suggested methods for different network setup: . the nvr is placed in a network with a dhcp server: connect to the nvr by using search nvr utility . the nvr is placed in a network without dhcp server (or you are connecting to it directly): access nvr with its default ip use levelone device search utility if the nvr is placed in a corporate network or a lo cal area network where a dhcp server is already presented, install the leve lone device search utility on the cd from a computer that is on the same netwo rk and locate the nvr with its ip address that is assigned by the top-lev el dhcp server. to begin, launch the levelone device search utili ty from the cd and proceed with the installation: 12 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder once the installation is complete, check the launc h the search ap option and click finish: the search should start automatically and its statu s should be displayed: the nvr should be located and its ip address should be displayed: double- click on it and the program should automatically ac cess the nvrs web administration page from your default browser you may change nvrs ip address by click on the but ton highlighted below. 13 13 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder you will be prompted for the nvrs login informatio n before proceeding to change devices ip address. you may click on the button highlighted below to pe rform search again. or double-click on any of the search results to access nvrs web administration page perform search again access nvrs web administration page you should be prompted for the nvrs username and p assword. enter its default username admin and password password and then click ok to enter the system 14 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder access nvr with its default ip address the nvr comes with a pre-configured static ip 192.168.101.50 . however, it is only used when there is no dhcp server presented in the network. the nvr will turn on its dhcp server function and act a s the dhcp server in the network. to connect to the nvr, use a pc that is on the same network over a switch or hub, or connect the pc directly to the nv r using a crossover cat5 ethernet cable. the pc that is connected directly to the nvr (or wi thin the same local area network) should receive an ip from it. simply acces s the nvr from your web browser with its ip address again, you should be prompted for the username and password. enter its default username root and password root and then click ok to enter the system 15 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 1. live view nvr-0216 camera list ptz control live video live video control buttons nvr-0208 the 8 channel nvr comes with an 8-video split windo w view with one video displays on a larger window. select a channel from the drop-down menu to display its video on the larger split window. you can also double-click on any of t he smaller one to display its video to the larger window. 16 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder NVR-0204 the live view page provides the following functio ns: . retrieve cameras video stream . retrieve cameras status . perform live sequence viewing . ptz control . perform ptz preset sequence viewing . perform manual recording . take snapshot . receive audio of a video stream . send audio . control buzzer . change web ui display language 17 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 1.1 retrieve cameras video stream the camera list is expanded and displayed on the live view page. . click all to display videos in the 8-video mode (nvr-0208) or 16- video mode (nvr-0216) . click on a group (ex. group 1) to display videos from cameras under that group in quad view . click on any camera to display video in single-view mode 1.2 retrieve cameras status the camera list can show each cameras current stat us. each status is represented with different colors and their meaning s are explained on the left camera is connected camera is not connected camera is current performing recording 18 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 1.3 perform sequence viewing sequence view is a function that allows you to view multiple video streams from certain cameras in sequence automatically with having to select them one by one. to perform sequence view, select seq view from th e upper-left hand corner next, select one or more camera(s) or camera group( s) for sequence viewing then select dwell interval from the drop-down menu finally click start to start sequence viewing * click all channels to quickly select all availa ble channels and start sequence view in single-view mode. click all groups to quick select all available gr oups and start sequence view in quad-view mode or simply select the desired channels and press st art to start sequence view the all group button is not available in 4ch nvr as it only has one group 19 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
engli sh use r s manual levelone network video recorder 1.4 ptz control ptz control provides functions to pan, tilt, zoom a ptz camera as well as the ability to adjust camera focus and iris camera(s) that are currently being selected for liv e viewing will be listed in the ptz drop-down menu. simply select a camera t hen use the ptz control panel to control the camera the bar shown below allows you to control the pan/t ilt speed 20 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 1.5 perform ptz preset viewing there are three functions provided in the preset section: . perform preset point viewing of a particular camer a . auto pan a particular camera . perform preset point sequence viewing preset point viewing start by selecting a ptz camera from the drop-down list: its available ptz preset points will be listed in the drop-down list shown below: select a preset position from the drop-down list an d click go to to move the live view to that position 21 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder auto pan viewing start by selecting a ptz camera from the drop-down list: use the auto pan control buttons to pan right, left and stop auto pan autopan pan left stop pan certain cameras do not support bidirectional pan movements. use the autopan button for such cameras pan right preset point sequence viewing this function allows you to view multiple preset po ints videos of a camera without having to select them one by on e. once you have defined the preferred preset points in camera configuration >> ptz preset sequence under the setup menu, click start here and the recorder will begi n to display videos from those preset points in sequence automat ically until you click stop 22 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 1.6 live video control buttons each live video window comes with control buttons w ith functions described below: take a snapshot of a live video turn on/off audio of a live video start/stop recording of a live video (manual record ing) audio post function full screen view of a live video display video in its original ratio 23 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder take a snapshot of a live video to take a snapshot of a live video, click the button and the snapshot of the video will be displayed in a pop up window shown like below right-click anywhere on the image and select save image as from the pull-down menu in the pop up dialog, name the image file and choos e which directory the image will be saved to and click save 24 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder full screen view of a live video to view a video in full screen, click the button. to exit full screen video, double-click anywhere on the video. turn on/off audio of a live video you can retrieve audio from a particular camera. si mply click the button to do so. the button will show in different color once the au dio is turned on. click on it again to turn off audio. you may only turn on audio once channel at a time start/stop recording of a live video you can manually start or stop recording of a live video by using the button. the button will show in different color once the re cording is started manually. click on it again to stop recording. audio post this function allows user to speak from a pc throug h a microphone and the audio can be played at the camera side if i t has a speaker connected to it. 25 levelone nvr series network video recorder levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 1.7 change web ui display language you can change the web ui display language from the current login username link located at the upper-right hand corne r. click on the link opens up a new window which displays detail informa tion about the user as well as a drop-down menu which lets you cha nge the display language. 26 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 2. playback methods to search playback playback video control buttons channels to be played back playback video playback is a function that allows you to play one or more videos that were previously recorded by a chosen recording method or due to an event trigger. the nvr offers synchronized playback from up to 4 channels and various types of search methods are provided to hel p you find the footage you need quickly. you can turn on or off the audio of a recorded vide o at your choice if audio was also recorded during the recording of the video . playback video can be viewed in full screen and sna pshots can be taken and saved during a video playback. 27 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 2.1 methods to search playback videos the nvr offers three methods to quickly help users find videos that were previously recorded: . search by time: specify a time range and search videos recorded wit hin that range . search by event: find videos that were recorded due to event trigger s . play by start time: enter a specific time a video was recorded to start playing back the video search by time chart . start by selecting which channel(s) you would like to perform a search on: * selected channels will be marked in red . select search by time chart from the search met hod drop-down list and click go to start the search: 28 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder . results will then be displayed in a date/channel table and boxes marked in blue represent videos found in those date s: . click on any blue cell box should direct you to th e hour/channel table if there were multiple videos recorded during that dat e: * videos from other cameras that are recorded on the same date will also be displayed * move the mouse cursor on a particular cell box wi thout clicking gives you a preview of the play-back video n a small thumbnail 29 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder . click on the cell box again will start playing bac k the videos if you have reached the end of search results: . videos found from other cameras that were recorded at the same time will also be played. 30 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder search by event . start by selecting which channel(s) you would like to perform a search on: * selected channels will be marked in red . select search by event from the search method drop-down list and click go to start the search: . results will then be listed like what is shown bel ow (displays the oldest record top down). click on a particular result to s tart the playback: * you can click next search to display the next 15 results. 31 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder . you may also specify a new start time to search an d display results from then on. you can restrict the number of results to be displayed at once (max. 30) and perform the search again play by specific time if you know when a recording was taken place, you m ay choose the play by start time from the search method drop- down list then you will be prompted to enter a specific time and date for the recorded video. use the button to select month, date, and year 32 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder search by event (most recent) this function quickly displays the most recent even t recordings from the selected channels, displaying the most recent resul t top down. you may click update to update the list to display the mo st recent result 33 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 2.2 export playback videos to avi files user can export the recorded playback videos stored on nvr-0216 to a local computer and save them in avi file format. the file s can then be played on the pc by a 3rd party media player such as vlc player o r windows media player. once you locate the recorded videos with steps desc ribed in the previous section, hit the export avi button on a video win dow of the video you wish to export. a new dialog will pop up and allows you to specify the time frame (or length) of the video you wish to export click the button to pull down the calendar to help you spe cify the month, date and the year 34 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder specify the starting and ending hours of the video by entering numbers in the text boxes hit the start button to start exporting. the file will be automatically named and saved under the c:\ partition you will be notified once the process is completed successfully the exported avi file will be saved under the c par tition * ffdshow is required in order to play the exported avi file with windows media player. you can get it at http://sourceforge.net/projects/ffdshow- tryout! to download the ffdshow_beta6_rev2527_20081219. exe 35 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3. system setup 3.1 system configurations the system configurations page provides users opt ions to setup the device quickly and properly. after properly configuring al l settings in all the sub-pages, users should expect a fully working network video r ecorder that is ready to manage cameras on the network. we will start by con figuring its network settings to make sure it works correctly in your ne twork. next, we will help you adjust the system time so videos will be recorder w ith correct timestamp. to better secure the system for unwanted disturbance, we will guide you on setting up users account and privileges to prevent setting s gets altered by users other than the system administrator. lastly, we wil l tell you what you should expect after installing a hard disk and how to prep are the hard disk for the video recording. 3.1.1 network settings you need to adjust settings in this page for the de vice to work properly in your network. it is critical that settings here are conf igured correctly based on your network configurations so that the recorder ca n be administered through the local area network and cameras can be connected from it. 36 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder by default, the recorder is set to obtain ip addres s from dhcp server, it should be sufficient in most network environments, and mos t likely you should not need to alter anything in this page. to locate the recorder, simply use the levelone ip utility with steps described in page 12 . if you wish to set the recorder to use a static ip address in your local area network, 1. choose static ip from the connection type dr op-down menu 2. enter the ip address, subnet mask, default gatew ay address and dns server address for the recorder 3. enable dhcp server under dhcp server if you wish to use the recorder as a dhcp server, or leave it disabled if there is already a dhcp server in the network 4. click apply for the settings to take effect change the recorders ip address would require the recorder to restart. restart the device under system options >> maint enance for the settings to take effect. the recorder can detect the presence of a dhcp server upon startup. it sets itself to use static ip address if there is no dhcp server currently presented in the network. its dhcp server function is also turned on at the same time to assign ip addresses to cameras that are later connected to the network. you can manually turn off the dhcp server function if you wish to use a separate dhcp server. 37 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
engli sh use r s manual levelone network video recorder 3.1.2 time and date set the time and date by selecting the time zone ac cording to your location. it is imperative that you set the recorders time c orrectly to avoid the following errors: ? incorrect display time for playback videos ? inconsistent display time of event logs and when th ey actually occur after selecting the time zone, choose an option bel ow to set the recorder time ? manual use the drop-down list and configure the time manua lly ? sync with ntp server enter the hostname or ip address of a valid ntp server and set how often the recorder should synchr onize the time with the recorder by using the update interval drop-down m enu ? sync with pc check this option to synchronize the recorder time with the pc that you are currently using to access the recor der 38 38 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.1.3 user account the recorder can be accessed by multiple users simu ltaneously. you can add, remove, and edit users by using options provided in this page to keep user information organized. each recorder comes with a b uilt-in admin account with password password. its highly recommended t o change the password upon your initial login. to change the password of the admin account: 1. click and highlight the admin account in the a ccount list and click edit 2. its information should be displayed in user acc ount information 3. enter a new password in the password field and enter it again confirm password to add a new user: ? enter a username and password in user account information. all other fields are optional for your own reference. ? select a group from the group drop- down menu to assign the new user to a particular group ? enter a short description for the account if you wish ? click apply to finish configuration 39 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
menu name english use r s manual levelone network video recorder 3.1.4 group privilege group privilege is where you can create multiple cu stomized access policies for situations if you need the recorder to be acces sed by users other than the administrator. you can do so by creating a group, a nd then remove access privileges for certain configuration pages or camer as. users that are created and assigned to this group will have limited access instead of full administration rights. the recorder comes with seven built-in groups and f ive built-in privilege profiles, except the admin and the guest accounts; the ot her five groups are fully customizable or you can simply assign a group with one of the default privilege profiles. you can, however, assign more t han one users to the admin account if you wish to do so. the guest acc ount comes with a view- only privilege in the live view page, and users in this group do not have the power to make any changes in the live view pa ge or have access to pages other than the live view page. to create a group, select a group from the group drop-down you can change the group name by clicking the chan ge group name button. a text box will be displayed for you to ent er the new group 40 40 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder choose what type of privilege you would like this g roup to have from the privilege type drop-down menu its access privilege will then be displayed. you ca n alter its settings by allowing or denying access to other cameras using t he checkboxes instead of accepting the defaults 41 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.1.5 disk setup once you install a hard disk to the recorder, you w ould need to initialize it so that it can be ready for recording. you can obtain basic information about the disk you installed in this page to initialize it, simply click the format button you can also connect external usb thumb drive to th e recorder for firmware upgrade. for instructions to install a hard disk to the reco rder, refer to page 9 to obtain detail information about the disk, go to system options >> disk status 42 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.2 channel configurations 3.2.1 add a camera the nvr provides two options for adding a new camer a. users have the option to let the recorder automatically find the c ameras or it is possible to enter cameras information and add it manually. automatic search: 1. click the search button to perform the camera search. you should be prompted to install active control component in ord er for the search to function properly. go ahead and click install 43 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 2. after that, the search should begin and its stat us should be displayed: 3. found cameras should be listed and simply select a camera from the list and press configure 4. its corresponding information should be displaye d in the camera information section. enter its username and passwo rd and select the channel id and name the camera. 5. click on detect to establish connection betwee n the recorder and the camera. if connection establishes successfully, cam eras detailed information should be polled and displayed as below 6. adjust its video format, frame rate, resolution or bitrateetc if you wish. you can also click on the preview to preview the live video of the camera. click add to finish adding the camera 44 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder if cameras are marked with * in the search result , it means those cameras are already configured and connected to nvr-0216. add a camera manually simply follow the instruction described above but i nstead of using the search function, enter the cameras ip addres s and credential in the camera information manually, then follow step 5 ~ 6 described above. 2. 1. enter manually 45 45 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.2.2 osd settings the osd (on screen display) allows users to add inf ormational text message and embed it onto the video. by default, this funct ion is turned off. to add texts to one or more videos, 1. select a camera you would like to add text to an d choose display osd 2. choose one or more display options if you would also like the recorder to automatically embed the system time or the frame ra te for you. or simply choose to display a custom message of your own 3. next, define where the text will be displayed by either entering an x/y coordinate or use the system pre-defined position f rom the drop-down menu 4. click on the preview button to see the preview of your setting and click apply to save the configuration . the texts can be further adjusted with changes to different size, color or font so they can be more visible on the video 46 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.2.3 ptz preset settings the recorder supports ptz cameras and can set multi ple preset points or retrieve and manage preset points that are set in t he camera. this is helpful if you need to monitor multiple spots in one area from a particular camera. 1. to set up ptz preset points, select a camera fro m the camera drop-down menu and click add 2. select a position number for the preset point fr om the position number drop-down menu and fill in a name in the position name field for easier identification 3. use the ptz control provided in the configuratio n page to set the preset point and set the position as the home position i f you wish. 4. click apply to save the configuration. 47 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s m anual levelone network video recorder 3.2.4 ptz preset sequence once you have multiple preset points defined for a camera, it is convenient for monitoring to set up the sequencing viewing among t hose preset point and let the recorder automatically switch between them for you. to configure preset sequence for a camera, select a camera from the camera drop-down menu the available preset points should be listed in ca mera presets section pick the ones you like for sequence viewing and pre ss the -> button to move them to the adjust position section, then use the up and down buttons to adjust their sequences finally, select a dwell time from the drop-down men u and click apply to save the configuration ? to start preset sequence viewing, check page 20 f or instructions 48 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.2.5 e-map monitor e-map monitor is a function that alerts users whene ver there is an event triggered (e.g. motion detected) from a camera with a geograp hical perspective. with this function, users can quickly identify which cam era has detected an unusual event and where this event is happening. this funct ion works by incorporating the event detection function as well as the recording f unction, which, as a result, helps users take all the necessary actions when an unusual event occurs. to replace the map, click browse button to locate the new map image file from the local pc and then click upload 49 49 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder then click and drag the camera icon to move the cam era to define its location. access the e-map monitor page from the upper-right hand corner menu when the nvr receives an event triggered from any o f the cameras, their videos will be displayed on the e-map and you can d ouble-click on the video to enlarge it 50 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.3 event configurations the event configurations section allows users to define conditions that constitute an event, its corresponding trigger acti on and when it will be triggered. such setting can reduce the management o verhead and notify the administrator only when its necessary. 3.3.1 general settings the general settings section can help you quickly c onfigure when an event is triggered, how often events are triggered and th e corresponding actions when events are triggered. start the event configuration by defining the gener al settings: define when an event will be triggered ? choose always or only during under event trig ger duration ? for the only during option, choose the days by u sing the check-box and then define the time range in those days in the st art time and end time fields that you would like the event trigger functi on to be enabled. how often an event is triggered ? set a time interval under event trigger interval to define how often events are triggered 5 51 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder trigger action now that you have the event trigger duration and in terval defined, choose what action to be taken during an event trigger: ? you can choose to have the recorder send out the fi rst few frames of the video recorder upon an event is triggered ? you can also choose to have the recorder send out a warning message in e- mail or in txt file format and upload it to a desti ned ftp server 3.3.2 i/o settings this function allows users to manage cameras digit al input and output ports right from the recorder. you can setup the recorder to receive triggers from a particular cameras input port and trigger a device , such as an alarm that is connected to the recorder or cameras output port. cameras that do not have built-in digital input/output port can also be conf igured to pair with the recorders di/do ports. 1. for cameras that come with physical digital inpu t ports, their ports will be listed in the far left drop-down menu. 2. pick the desired channel for i/o mapping, and th en select the cameras input port from the drop-down menu. 3. select the trigger condition from the condition drop-down menu. 4. select the recorders input port if you would al so like to use the recorders input port for event trigger. and then select the t rigger condition as well. 5. next, select the recorders output port and the trigger action 5. finally, define the trigger duration. 52 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder the recorder does not control cameras input or out put ports in a way to let you pair recorder itself with a cameras input or output por t for event receiving or triggering. the recorder only acts as a medium for pairing up i nput/output ports between cameras and the recorder. only connected cameras will be displayed in the lis t. some cameras only allow one trigger source be confi gured at a time, e.g.: if the camera has the motion detection function turned on, its digital input will be disabled and vice versa. under such circumstance, if you set to use cameras digital input port as the event trigger source, you will not be able to select moti on detection as the trigger source for this camera under event configurations >> event trigger setup page. 53 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.3.3 event servers event servers are to be used with event trigger act ions. in case of unusual motion detected by the camera or a disk failure, th e recorder can send notification with the acceptable format (image/txt) to a destined event server according to the configuration. configuring an ftp server to add an ftp server, 1. start by giving a name to the server that you ar e adding to the recorder 2. enter the hostname or the ip address of the ftp server 3. enter the communication port of the ftp server ( usually port 21) 54 http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 4. enter the username and password of the ftp serve r if its required 5. check use passive mode if its required or lea ve it unchecked to use active mode 6. click test to verify if all information is ent ered correctly and the connection to the ftp server can be established successfully 7. click apply for the settings to take effect if you wish to edit/remove/enable/disable an ftp se rver, click to highlight one from the profile list and choose the corresponding action bu tton 55 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder configuring an http server 1. start by giving it a name as well 2. enter the hostname or the ip address of the http server 3. enter the port thats used to communicate with t he server 4. enter the username and password if its required 5. click test to verify if the information is ent ered correctly 6. click apply for the settings to take effect 56 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder configuring an smtp server 1. enter the hostname or the ip address of the smtp server 2. enter the port of the smtp server 3. specify the senders name in the senders name field 4. enter the senders e-mail address 5. check enable authentication and enter the user name and password of the smtp server and it requires authentication 6. click apply to save the configuration 57 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
e nglish use r s manual levelone network video recorder 3.3.3 event triggers we have finished defining how an event will be trig gered and which servers will be receiving notifications in the previous two sections, now we can finish up the event configuration by setting: . which channels will have event trigger function en abled . what is considered to be an event . where the warnings will be sent to and how they wi ll be sent select channels to enable event trigger and which t ype of event should be triggered . use the checkbox to enable event trigger on the de sired channels 5 58 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder . define which system events should trigger the reco rder to send out notifications . define how the notifications will be sent and wher e they will be sent to * event trigger may not work for cameras that are p laced outside of your local network or on the internet until the upnp port forwarding is enabled in both the nvr and the router. 59 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.4 recording configurations the recording configurations gives users the over all control of how and when a recording is performed and the quality of differe nt types of recordings performed on each channels. it can help the recorde r to operate with sufficient system resource by performing recording only when i ts necessary with adjustable recording frame rate. 3.4.1 general settings you can define the following in general settings: . pre-alarm/post-alarm recording length . recording frame rate . enable/disable different recording types on differ ent cameras 60 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder the recording configurations gives users the over all control of how and when a recording is performed and the quality of differe nt types of recordings performed on each channels. it can help the recorde r to operate with sufficient system resource by performing recording only when i ts necessary with adjustable recording frame rate. recording frame rate allows you to set different fr ame rate for different types of recording instead of recording at one frame rate only. use the drop-down menu and select one of the pre-defined frame rates for a particular recording type the section at the bottom allows you to turn on or off a particular recording type on any channels. 61 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.4.2 schedule recording here you can define the time range of the schedule recording for all channels. to configure a schedule recording: 1. use the camera drop-down menu and select a cam era first 2. you can use the schedule table to set the time r ange. click the cell boxes then move the curser horizontally lets you set what hours to perform recording during a day. click and move vertically l ets you set what days to perform recording at a specific time. * each cell box represents 15 minutes of time. clic k one or more boxes to omit consecutive recording 62 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3. you can also use the quick configuration to de fine recording time range instead of clicking cell boxes one by one on the time table. simply check what days you would like to perform recording and specify the recording duration by either choosing all day or enter a st art and end time for specific recording duration. 4. select the copy to option if you would like to set the same recording schedule to another camera. 63 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.5 system options system options gives users a glance of the overall system status and allows users to perform maintenance tasks such as upgradin g firmware, restore/backup device settings or reboot device .e tc. 3.5.1 device information the device information provides the general infor mation of the device such as firmware version and system time. it also p rovides information of the current network settings and status. 64 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.5.2 logs and reports logs and reports keeps a record of whats been ha ppening to the device and provides basic information for troubleshooting 3.5.3 maintenance maintenance provides functions for users to: . reboot the nvr when necessary . reboot cameras directly from the nvr . perform firmware upgrade . backup the nvrs settings to a local hard drive . restore the nvrs settings from a previously saved configuration file . reset the nvrs settings to their factory default v alues 65 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder reboot the nvr reboot nvr-0216 after you upload a new firmware. yo u would need to manually reboot the system for the new firmware to take effect. such process would prevent a recording from getting inte rrupted because the system would not automatically reboot itself after the new firmware is loaded onto the recorder. simply click restart to begin the reboot process and confirm the action: the restart process should be displayed and you sho uld be prompted back to the maintenance page after it is complete: 66 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder reset the nvr to factory default to reset the recorder back to its factory default, click default button and begin the process: the process should be displayed and you should be p rompted back to the maintenance page after it is complete: hardware reset procedure: 1) find the reset button at the front panel of the nvr unit 2) use a pin to press the reset button for 45 secon ds. you would see power led start flashing as you press it. when you press for 45 seconds, all led will become solid red and release the pin. 3) wait for 1 minute for the unit to reboot. when reboot successfully, the leds of power, status, network and hd should return to gree n. 67 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder 3.5.4 do status this is where you can get the current status of the nvr-0216 digital output ports. you can also change their status from this p age. 3.5.5 disk status disk status gives you more detailed information o f the hard drive that is currently installed in the nvr. 68 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s m anual levelone network video recorder 3.5.6 ups configuration connect the ups to the nvrs di/do port for sending and receiving signals between the ups and the nvr. refer to the diagram b elow to connect the ups with its rs-232 interface to the nvrs di/do po rt. the nvr can receive signal from the ups when there is a power failure and shut down itself automatically within a period of t ime. connect ups with its rs-232 interface to the nvrs 10 port: * the nvr uses di_1 to receive signal from ups syst em and uses do_1 to shut it down. 69 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/
english use r s manual levelone network video recorder nvr recording time table for reference (it maybe different test result with each environme nt) 70 levelone nvr series network video recorder http://www..net/ datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of NVR-0204

	To Download NVR-0204 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .